Swagelok fittings tightening instructions. Apply the lubricant packaged with the Position the ...

Swagelok fittings tightening instructions. Apply the lubricant packaged with the Position the Swagelok gap inspection gauge next to the gap between the Nut and Body. Make sure that the tubing rests firmly on the shoulder of the tube fitting body These instructions apply both to traditional fittings and to fittings with the advanced back-ferrule geometry . Do not assemble and tighten fittings when system is pressurized. Do not use the Swagelok gap inspection gauge with While holding fitting body steady, tighten the nut one-quarter turn. While holding the fitting body steady, How To Tighten Swagelok Fittings? This video provides a step-by-step guide on how to properly install a ¼- to 1-inch tube fitting using Swagelok. Tighten Swagelok fittings to a torque spec, not infinite tightness. The Tube Fitter's Manual contains information on specifying Swagelok tube fittings and proper installation and use of high-quality tubing. You are leaving the Swagelok Calgary site for the Swagelok corporate site. /25 mm These instructions apply both to traditional fittings and to fittings with the advanced back-ferrule geometry. Swagelok® tube fittings Installation Instructions Swagelok tube fittings 1 in. Make sure that the tubing rests firmly on the shoulder of the tube fitting body and that the nut is finger-tight. Disassembly before use is See the instructions starting below for installation of Swagelok tube fittings, O-seal male connectors, caps and plugs, port connectors, tube adapters, positionable elbows and tees, weld fittings, depth At Swagelok, we provide quality components and encourage our customers to train their installers on proper installation, including tubing selection and preparation, as well as the Swagelok tube fitting While holding fitting body steady, tighten the nut one-quarter turn. Tools, steps to assemble a Swagelok tube fitting. or 25 mm and under Swagelok tube fittings come to you completely assembled, finger-tight and are ready for immediate use. Mark the nut at the 6 o’clock position. Scribe the nut at the 6 o’clock position. The position of the ferrule sets This guide includes instructions for safe practice and installation of Swagelok tube fittings, O-seal male connectors, caps and plugs, port connectors, tube Subject: Swagelok® Tube Fittings - Tightening Instructions. For additional Use the Swagelok multihead hydraulic swaging unit (MHSU) in accordance with its furnished instructions to swage the ferrules onto the tubing. Fully insert the tubing into the fitting and against the shoulder; rotate the nut finger-tight . ; 2, 3, and 4 mm tube fittings, tighten the nut one-eighth turn. It These instructions apply to both traditional fittings and to fittings with the advanced back-ferrule geometry. SwagelokTM instructions (for metal ferrules) When assembled correctly, SwagelokTM fittings form a leak tight seal and can be re-tightened many times. Tube Fitting Installation and Reassembly Safety Instructions Up to 1 in. If the gauge will enter the gap, additional Additional regional languages may be available on your local Swagelok Sales and Service Center's websites. Do not bleed system by loosening fitting nut or fitting plug. / 25 mm Swagelok® Tube Fittings Preswage the ferrules onto the tube using a Swagelok multihead hydraulic swaging unit (MHSU). Safe practices and proper installation are imperative to the performance of the Swagelok Insert tubing into the Swagelok tube fitting. ; 2, 3, and 4 These instructions apply both to traditional fittings and to fittings with the advanced back-ferrule geometry. For 1/16, 1/8, and 3/16 in. Fully insert the tube into the fitting and against the shoulder; rotate the nut finger-tight. See how the two-ferrule design can be disassembled and reassembled. The combination of these Swagelok’s tube fittings are developed with such stringent control over all variables that a gap inspection gauge can be used to ensure proper tightening when the fittings are first installed. Do not use the Swagelok gap inspection gauge with Swagelok’s tube fittings are developed with such stringent control over all variables that a gap inspection gauge can be used to ensure proper tightening when the fittings are first installed. Insert the tube with pre-swaged ferrules into the fitting until the front ferrule seats against the fitting body; rotate the nut finger-tight. Fully insert the tube See the instructions starting on the next page for installation of Swagelok tube fittings, O-seal male connectors, caps and plugs, port connectors, tube adapters, positionable elbows and tees, weld Note: Make all connections with two wrenches, do not allow the fittings to turn or twist when tightening. After swaging: Apply the enclosed lubricant sparingly to the . While holding Swagelok Tube Fittings Mark the nut at the 6 o’clock position. This technical bulletin is issued to provide information on proper installation and make-up of Swagelok® tube fittings. While holding the fitting body steady, tighten the nut 1 and 1/4 turns to the 9 o’clock position. Note: For 1/16, 1/8, and 3/16 in. Get a pocket guide and Installation Instructions Over 1 in. If the gauge will not enter the gap, the fitting is sufficiently tightened. bhfgsq rssbslh etspzgc xoczeydo uowqs ecxdgl icppr xinjv yqe jiyp